[Kolab-devel] wallace woes, kolab-3.0

[Henning]

As a side-note: Inbound AND outbound mail got stuck, but not all.

Am 02.02.2014 11:35, schrieb Henning:
> Hi,
> 
> I ran into this problem too. I disabled wallace in master.cf an requeued
> stuck mail via
> 
> ~$ sudo postsuper -r ALL
> 
> to solve this. I have kolab 3.1 installed on Ubuntu. Would you have a
> look at it?
> 
> Henning
> 
> On Thursday, November 21, 2013 05:23:47 PM Thomas Spuhler wrote:
>> On Thursday, November 21, 2013 04:16:06 PM Geoff Nordli wrote:
>>> On 13-11-21 02:28 PM, Thomas Spuhler wrote:
>>>> On Thursday, November 21, 2013 11:26:35 AM Thomas Spuhler wrote:
>>>>> Does anybody know how to disable mail being routed through wallace?
>>>>> I have commented out everything I can find in relation to
> wallace, but still get this:
>>>>>
>>>>> (host 127.0.0.1[127.0.0.1] said: 451 4.5.0 id=03681-05 -
> Temporary MTA failure on relaying,
>>>>> from
>>>>> MTA(smtp:[127.0.0.1]:10026): No resp. to data-dot (in reply to
> end of DATA command)
>>>>>
>>>>> I restarted postfix after making the changes in master.cf and
> resent the e-mail
>>>>> (yes, in this case, it's an outgoing e-mail.)
>>>>
>>>> I may got a reply to this, but it got stuck in wallace?
>>>
>>> Yes, it stays in there (I had the same probably you did a few days ago).
>>>
>>> Try this:
>>>
>>> run postqueue to get a list of the messages and their IDs:
>>>
>>> postqueue -p
>>>
>>> then try requeuing it with the:
>>>
>>> postsuper -r message_id
>>>
>>> Geoff
>>>
>>>
>>> _______________________________________________
>>> users mailing list
>>> users <at> lists.kolab.org
>>> https://lists.kolab.org/mailman/listinfo/users
>>
>> Thanks Geoff:
>> I tried this already.
>> The questions is actually, why does it still get into wallace?
> 
>> I just found an error log about it. I am going to add the dev list:
>>
>> Nov 21 17:45:12 aargau.btspuhler.com wallaced[18598]: error:
>> uncaptured python exception, closing
>> channel <smtpd.SMTPChannel connected 127.0.0.1:52259 at 0x1676368> >(<type
>> 'exceptions.UnicodeDecodeError'>:'utf8' codec can't decode byte 0x96
>> in position 3308: invalid start
>> byte [/usr/lib64/python2.7/asyncore.py|read|83]
> [/usr/lib64/python2.7>/asyncore.py|handle_read_event|
>> 449] [/usr/lib64/python2.7/asynchat.py|handle_read|158]
> [/usr/lib64/python2.7/smtpd.py|
>> found_terminator|181]
>> [/usr/lib/python2.7/site-packages/wallace/__init__.py|process_message|271]
>> [/usr/lib64/python2.7/json/__init__.py|dumps|250]
>> [/usr/lib64/python2.7/json/encoder.py|encode|209]
>> [/usr/lib64/python2.7/json/encoder.py|_iterencode|434]
> [/usr/lib64>/python2.7/json/encoder.py|
>> _iterencode_dict|390])
>>
>> --
>> Thomas Spuhler
> _______________________________________________
> devel mailing list
> devel at lists.kolab.org
> https://lists.kolab.org/mailman/listinfo/devel
>