new Horde release

[Ger Apeldoorn]

Well, It was a bit of a hassle to install the extra openpkg packages...

Note that this is from memory, so it might be not so accurate:

1) download some openpkg packages from www.openpkg.org: (you've got to 
register)

address: ftp://[username]@ftp.openpkg.org/release/2.5/SRC/

   jpeg-6b-2.5.0
   png-1.2.8-2.5.0
   freetype-2.1.10-2.5.0
   gd-2.0.33-2.5.0
   mysql-4.1.14-2.5.0
Save them in the same location as where the other kolab installation files 
are. (same dir as obmtool.conf)

2) Append the following to obmtool.conf:

%horde
   echo "---- boot/build ${NODE} %${CMD} ----"
   kolab_version="2.0.3";
   PREFIX=/kolab;
   loc='./' #  (empty) for ftp.openpkg.org, '=' for URL, './' for CWD or 
absolute path
   plusloc='+'
   altloc='./'
   remote=
   with_genuine=no
   @install ${loc}jpeg-6b-2.5.0
   @install ${loc}png-1.2.8-2.5.0
   @install ${loc}freetype-2.1.10-2.5.0
   @install ${loc}gd-2.0.33-2.5.0
   #@install ${plusloc}libmcrypt-2.5.7-2.5.0
   @install ${loc}mysql-4.1.14-2.5.0
   @trigger ${altloc}apache-1.3.33-2.4.5_kolab \
       --with=mod_auth_ldap \
       --with=mod_dav \
       --with=mod_php \
       --with=mod_php_zlib \
       --with=mod_php_ftp \
       --with=mod_php_gd \
       --with=mod_php_gdbm \
       --with=mod_php_gettext \
       --with=mod_php_iconv \
       --with=mod_php_imap \
       --with=mod_php_mysql \
       --with=mod_php_openldap \
       --with=mod_php_xml \
       --with=mod_php_dom \
       --with=mod_ssl \
       --with=mod_php_mbstring
   @trigger ${altloc}php-4.3.11-2.4.2_kolab \
       --with=zlib \
       --with=ftp \
       --with=gd \
       --with=gdbm \
       --with=gettext \
       --with=iconv \
       --with=imap \
       --with=mysql \
       --with=openldap \
       --with=pear \
       --with=xml \
       --with=dom \
       --with=ssl \
       --with=mbstring
   @check

3) run /kolab/bin/openpkg rc all stop

4) Run ./obmtool horde and watch for errors

5) You might need to rerun bootstrap, but i am unsure about this. <- will 
destroy your kolab configuration!!

6) run /kolab/bin/openpkg rc all start

7) now you need to place the downloaded horde directory 
in /kolab/var/kolab/www and follow the horde/config/INSTALL directions

Then it should work (TM)

Good luck!

Ger.

Op donderdag 9 maart 2006 12:14, schreef u:
> Hi
>
> I'm interessted in this it means what did you do exactly to install Horde
> (docu available?) and how do you use Kolab2 it means with Toltec Connector
> and fully XML 2.0 standard, Outlook etc?
>
> Andrea
>
> > Hi,
> >
> > I've installed it and it looks good! Just give it a go!
> >
> > Ger.
> >
> > Op woensdag 8 maart 2006 04:55, schreef Markus Heller:
> >> Dear List,
> >>
> >> Heise news says that the new Horde released yesterday has kolab support.
> >> Does anybody know more?
> >>
> >> Best wishes,
> >> Markus
> >>
> >> _______________________________________________
> >> Kolab-users mailing list
> >> Kolab-users at kolab.org
> >> https://kolab.org/mailman/listinfo/kolab-users
> >
> > _______________________________________________
> > Kolab-users mailing list
> > Kolab-users at kolab.org
> > https://kolab.org/mailman/listinfo/kolab-users
>
> Mit freundlichen Grüssen
>
> Andrea Soliva
>
> Comcept Net GmbH
> Feldhof 1
> CH - 6343 Rotkreuz/ZG
>
> Tel:   +41 (0)41 790 48 39
> Fax:   +41 (0)41 790 48 51
> Mobil: +41 (0)79 753 33 82
>
> Mail: soliva at comcept.ch